Troubleshooting Clogged Extruder/Nozzle In 3D Filament Extruder Machine

Are you having any problem with your 3D printer? If yes, worry not!

 

The fact is that 3D printers can fail at times, but most problems are simple to repair just with little patience and the use of basic tools.

 

Presently, we are going to attend to the major problem you possibly might face when operating 3D printing.

 

Also, we will put you in a simple way you can repair it. Honestly, you do not need to become a professional to understand our easy methods in the 3D troubleshooting guide.

 

Therefore, continue reading up accordingly to get your device up running again.

 

However, you may also want to consider getting a high-quality 3D filament extruder machine, a simple way to go about it is by contacting a professional 3D filament extruder machine manufacturer.

 

Here is a possible problem that can be encountered and solutions;

 

The problem of Clogged extruder/nozzle

In one way or the other, most users of the 3D printer encounter a clogged extruder.

 

Most times, the situation is associated with terrible vibrating noise and no release of filament when you start printing.

 

Also, under extrusion can be caused by a partially clogged nozzle. Signs like holes, thin layers, or cracks in your completed design are signal that there is under extrusion in our printer.

 FLD-45A 3D Printing Filament Extrusion Line

 

How does an extruder become clogged?

 

With time, the main observation is that the remaining filament in a pin-sized nozzle can be clogged in the nozzle or can be obstructed by other particles like dust.

 

Therefore, printing at the appropriate temperature with the use of filament that is of high-quality considerably reduces the chance of blocking the nozzle.

 

Also, keeping the extruder clean and lubricated with regular maintenance will protect it from been clogged.

 

The solution to clogged extruder/nozzle

Solution 1. 

Firstly, extract the filament from the printer. After, apply heat to the extruder in such a way that it will be at the same melting temperature of the previous filament used or most used.

 

After then, gently pull a needle or any other small tool that can fit the ~.4mm extruder through its hole. Although it may require some tries, it works better for dust problems or PLA.  

 

Solution 2.

Another popular method is by cold pulling. It clears a clogged extruder and it works better with filaments that flexible like nylon.

 

Firstly, you will heat the extruder to the temperature of the filament, and then manually thrust enough filament, without putting much pressure, through the nozzle.

 

Then, allow the nozzle temperature to cool to around 100C. Immediately, you will extract the filament out of the nozzle.

 

During the extraction, it pulls out any obstacle along with the filament. Then, pin the end part of the filament and restart to resume printing again.

 

If everything fails, therefore, you have to pieces your extruder or you can soak the extruder in a solution to remove the obstacle. But commonly, one of the described methods will work well.

 

Perhaps, if you still find it difficult to practice, then you may consult professional 3D Filament Extruder Machine manufacturer for proper guidance.

 

Summary

It is no more news that 3D printers can fail at times. However, the problems can be managed by repairing them with the use of basic tools.

 

However, for any problem that is beyond control, it may require that you contact a reputable 3D Filament Extruder Machine manufacturer.

 

More so, for the best deal when sourcing for 3D filament extruder machine, always consider doing so from a professional supplier with an outstanding record of excellence.

Share This Post

Contact Now

How would you like to be contacted?
* We respect your privacy. When you submit your contact information, we agree to only contact you in accordance with our Privacy Policy.